Operating instructions, Description of icons, Dip switch options and functions
DESCRIPTION OF ICONS
Display icons vary according to the model. Your thermostat may
not display all of the icons shown.
Robertshaw 300-201 manuals and user guides for free. Read online or download in PDF without registration. Manuals Directory ManualsDir.com - online. Robertshaw manuals. Water boiler. 300-201 Manuals; Manuals. Robertshaw 300-201 Instruction Manuals and User Guides. We have 1 Instruction Manual and User Guide for 300-201 Robertshaw. Get Robertshaw 300-208 User Manual. Get all Robertshaw manuals! Sign up to create an account Facebook Twitter. By clicking Create Account, you agree to the Company’s. The thermostat will once again display the indoor temperature. If the option is not connected, the thermostat will display -. Don't see a manual.
Outdoor Hi & Lo Temperature Balance Points (Heat Pump Only)
With the optional Electronic Outdoor Temperature sensor, you can
select the outdoor balance points to inhibit the auxiliary heat
and/or compressor.
HibP – Press and hold the OUTDOOR button, then press the
MODE button. HibP will appear on the display. Raise or lower the
HibP by pressing the
§ or ¨ button to set the temperature above
which the Auxiliary heat is locked out. Press the outdoor button
while showing the HibP and the thermostat will switch to show
LobP. LobP is used to lock out the compressor. Outdoor temper-
atures below the LobP will lock out the compressor. The factory
HibP and LobP setpoints are +48°C and -48°C.
DIP SWITCH OPTIONS AND FUNCTIONS
Positioning the DIP switches in either the ON or OFF position
enables you to choose between two different options. The DIP
switches are located on the interior of your thermostat and may
be accessed by following the procedure for removing the thermo-
stat from the subbase. The following list describes your DIP
switch options.
DIP Switch No.
DIP Switch OFF
DIP Switch ON
1
Normal
Add on
2
Not used (OFF position)
Not used
3
4 minute minimum ON
2 minute minimum
ON
4
Keypad unlock
Keypad lock
5
Economy
Comfort
6
Not used (OFF position)
Not used
7
LED #1+No icon
LED #1+
7
Filter icon
8
LED #2+No icon
LED #2+
6
Fault icon
1. Normal or Add On Heat Pump In the NORMAL position the ther-
mostat will allow the compressor and the auxiliary heat to be on at
the same time. In the ADD-ON position, the compressor is turned
off with a call for auxiliary heat.
2. Not Used This switch must remain in the OFF position.
3. 2 Minute or 4 Minute ON Times This option allows you to run the
equipment for either a 2 or 4 minute minimum off and on time.
4. Keypad Lock
5
In the ON position locks out all buttons except the
OUTDOOR temperature button.
5. Economy/Comfort In the OFF position, the thermostat will be in
ECONOMY mode. In the ON position the thermostat will be in
COMFORT mode.
6. Not Used This switch must remain in the OFF position.
7. LED #1 + Indication In the OFF position LED #1 will light when the
terminal is energized. In the ON position LED#1 will light and a
Filter
7
icon will be displayed on the LCD when the terminal is
energized.
8. LED #2 + Indication In the OFF position LED #2 will light when the
terminal is energized. In the ON position LED#2 will light and a
Fault
6
icon will be displayed on the LCD when the terminal is
energized.
SPECIFICATIONS
Rated Voltage
20-30 VAC, 24 nominal
Rated A.C.
0.050 Amps to 0.75 Amps continuous
Current
per output with surges to 3 Amps Max.
Rated D.C.
0 Amps to 0.75 Amps continuous
Current
per output with surges to 3 Amps Max.
Control
Heating: 38° to 88°F in 1° Steps
Range
5° to 30°C in 1° Steps
Cooling: 60° to 108°F in 1° Steps
Robertshaw Thermostat 300-208 User Manual Pdf
16° to 40°C in 1° Steps
Thermostat
Measurement Range
28° to 124°F or 0° to 48°C
O.D.T. Displayed
Range
-50° to 119°F or -48° to 47°C
Control Accuracy
±0.5°C at 20°C, ±1°F at 68°F
Minimum
(between heating and cooling)
Deadband
2°F or 1°C
NOTE: This thermostat contains electronic circuitry replacing the conven-
tional mechanical anticipator.
One (1) Year Limited Warranty
The manufacturer warrants to the original purchaser that its
product and component parts will be free from defects in
workmanship and materials for a period of one (1) year from
the date of purchase. Return to the original point of purchase
for replacement of your product.
Warranty Limitations
This warranty begins at date of purchase.
Warranty is Void if:
The date code is defaced or removed.
The product has a defect or damage due to product alteration,
connection to an improper electrical supply, shipping and han-
dling, accident, fire, flood, lightning, or other conditions beyond
the control of the manufacturer.
The product is not installed according to the manufacturer’s
instructions and specifications.
The product has been installed near sources of electromagnet-
ic interference (EMI) such as arcing relay contact.
Owner’s Responsibility
Provide proof of purchase.
Provide normal care and maintenance.
Pay for freight, labor and travel.
Pay for service calls related to product installation.
Return any defective product.
In no event shall the manufacturer be liable for incidental or
consequential damages.
This warranty gives you specific legal rights and you may have
others which vary by state and/or province. For example, some
states and/or provinces do not allow the exclusion or limitation
of incidental or consequential damages so this exclusion may
not apply to you.
The manufacturer’s continuing commitment to quality products
may require a change in specifications without notice.
This equipment, if installed in strict accordance with the manu-
facturer’s instructions, complies with the limits for a Class B
computing device pursuant to Subpart J of Part 15 of FCC rules.
NEW & IMPROVED FEATURES
Your new electronic thermostat has been made even better by the
introduction of several new and improved features. Building on its
reputation for efficient and dependable operation, your thermostat
now offers the following list of enhancements.
Thermostat and Sensor Calibration
Release 3 provides easy calibration of the thermostat and remote
sensors. Simply press and hold the FAN button for 10 seconds
and adjust with the
¨ or § buttons.
Push Button Auto Repeat
Programming is easier with the push button auto repeat feature.
GENERAL INFORMATION
The thermostat normally displays room temperature, mode of
operation and whether cooling or heating is currently on. The
six buttons on the front of the unit allow complete control of
your equipment.
You may select different heating and cooling setpoints for the
system to maintain, e.g., 70° in heating and 75° in cooling.
Raising or lowering the setpoints in heating or cooling is as sim-
ple as pushing a button. In addition, you may choose to display
the temperature in °F or °C.
The thermostat also allows you to select continuous fan operation
(useful when using an air cleaner) or have the fan come on with
the equipment.
BUTTON FUNCTIONS
Outdoor
Press to display the outdoor temperature (optional)
Mode
Press to select cool only, heat only, auto (cool &
heat), off or emergency heat
Fan
Press for continuous fan or auto fan
Day/Night
Press to alternate between day and night
temperature setpoints
USER CONTROLS
MODE
Select the desired mode of operation by repeated pressing of the
MODE button:
0011
– Indicates cooling system only (the word COOL is
displayed for 5 seconds)
0019
– Indicates heating system only (the word HEAT is
displayed for 5 seconds)
0019 0011
Opel astra manual. Motor Era has the best selection of service repair manuals for your 2004 Opel Astra - download your manual now! Money Back Guarantee! 2004 Opel Astra service repair manuals. Vauxhall Opel Holden 1987 to 2011 vehicles workshop manuals; HOLDEN ASTRA AH OPEL ASTRA H 2004-09 WORKSHOP SERVICE MANUAL; OPEL ASTRA H 2004-2011 FULL SERVICE REPAIR MANUAL. Page 1 OPEL ASTRA Owner's Manual. Fuel consumption - CO Emissions The fuel consumption (combined) of the model Opel Astra is within a range of 6.2 to 3.3 l/100 km. Page 208: Trailer Hitch Driving and operating Trailer hitch The CO emission (combined) is consumption and CO figures. Within a range of 142 to 88 g/km. View and Download Opel ASTRA owner's manual online. ASTRA Automobile pdf manual download. The fuel consumption (combined) of not be taken as a guarantee for the no lamp remains. The model Opel Astra is within a range actual fuel consumption of a of 3.7 to 8.1 l/100 km. Fitting of towing equipment could particular vehicle.
– Indicates both the heating & cooling systems
(the word AUTO is displayed for 5 seconds)
0011
– Blinking indicates cool ON
0019
– Flickering indicates heat ON
OFF – Disables controller so equipment will not operate
(fan operation is still possible in this mode)
Eht
– Emergency heat
COOLING:
0011
Select the temperature you want your equipment to maintain while
in the COOLING mode by pressing and holding the
¨ or § but-
tons. The control setpoint temperature is displayed for 5 seconds.
HEATING:
0019
Select the temperature you want your equipment to maintain
while in the HEATING mode by pressing and holding the
¨ or §
buttons. The control setpoint temperature is displayed. Your new
electronic digital thermostat has been designed to provide accu-
rate control and display of room temperature. It will also display
all relevant information of the system.
FAN:
0012
The fan will come on automatically when the system is operating,
but there is no indication of this on the display. To select continu-
ous fan operation, press the FAN button and the display will
show
0012
. This is recommended for electronic air cleaners and
continuous ventilation requirements.
TEMPORARY TEMPERATURE OVERRIDE WITH
KEYPAD LOCKED
(The keypad may be locked to prevent tampering by selecting the
ON position of DIP switch #4.)
If the keypad is locked to prevent tampering you may still tem-
porarily adjust the setpoint by ± 3° F or ± 3° C of the pro-
grammed day setpoint. Press the
¨ or § button to raise or lower
the setpoint for a 1-hour period.
OFF MODE
To turn off the heating or cooling system, press the MODE button
until the word OFF appears on the LCD. It will remain displayed
until the mode is changed. The OFF mode prevents the system
from being energized.
Avoid using the OFF mode during extremely cold weather to pre-
vent damage to the equipment from freezing.
AUTO CHANGEOVER MODE
00190011
You may set the thermostat to automatically switch from HEAT-
ING to COOLING mode by pressing the MODE button until the
word AUTO and both the heating
0019
and cooling
0011
icons appear
on the LCD. The thermostat will energize the heating or cooling
system based on the temperatures established for both modes.
Operating Instructions
Single Compressor Heatpump
with Auxiliary Heat
Non-Programmable Thermostat
Model 300-208
111-110B
USER CONTROLS (CONT)
OUTDOOR (ODT) BUTTON
If your thermostat has been installed with an electronic outdoor
remote sensor (Uni-Line Part #10-529), you may view the outdoor
temperature simply by pressing the OUTDOOR button. Upon
releasing the button, the thermostat will once again display the
indoor temperature.
If the option is not connected, the thermostat will display
(
---.
DAY/NIGHT BUTTON
2©
When the thermostat is initially installed, the display will show the
2
symbol for your day temperature. By pressing the DAY/NIGHT
button you may select an alternate or night temperature
©
(the
thermostat will remember this setpoint). Simply press the
DAY/NIGHT button to alternate between temperature settings.
CELSIUS / FAHRENHEIT
Simultaneously press
¨ and § to switch between Celsius (C) and
Fahrenheit (F) temperature display.
REMOTE SENSOR (OPTION)
RS1 – RS2 – RS+V
The thermostat is designed to accept the electronic remote
sensor (Uni-Line Part #10-528), which will allow you to locate your
thermostat in an area away from view. Indoor and outdoor sen-
sors are available separately.
CLOCK TERMINALS (OPTION) CLK1 – CLK2
Your thermostat is equipped with a dry contact closure input. By
connecting to any relay-based controller or clock timer (DSP-AT or
equivalent), the thermostat can be alternated between the
DAY/NIGHT (setback) temperature setpoints automatically. Upon
initial power up of the thermostat or after a power failure, the ther-
mostat will check the clock terminals and apply the DAY (open con-
tact) or NIGHT (closed contact) temperature setpoints accordingly.
ECONOMY / COMFORT
In the ECONOMY mode (switch #5 OFF) your thermostat will not
allow the equipment to be forced on with a change to the temper-
ature setpoint. In the COMFORT mode, the equipment will turn on
immediately with a change to the temperature setpoint.
TEMPERATURE ACCURACY
Full temperature accuracy will only be realized after the thermo-
stat has been installed and powered for at least one (1) hour.
ADD-ON HEAT PUMPS
Your DSL thermostat is equipped to enhance the performance of
an add-on heat pump. Your thermostat, in most applications, will
perform the function of a fossil fuel kit.
To select Add-On, place switch #1 to the ON position. The ther-
mostat will turn the compressor off with a call for auxiliary heat.
When the switch is set to NORMAL, the thermostat will allow the
compressor and the auxiliary heat to be on at the same time.
POWER FAILURES
Your thermostat employs the latest in solid state electronic
technology.
One of the unique features of your thermostat is that there is no
battery required to maintain your selected setpoints in the event
of a power loss as the memory is unaffected by power failures of
any duration.
When power is restored, the thermostat will continue operating as
if the power had never been off.
INSTALLATION INSTRUCTIONS
LOCATION
To ensure proper operation, the thermostat should be mounted on
an inside wall in a frequently occupied area of the building. In
addition, its position must be at least 18' (46cm) from any outside
wall, and approximately 5' (1.5m) above the floor in a location
with freely circulating air of an average temperature. You should
avoid the following locations:
– behind doors or in corners where freely circulating air is
unavailable;
– where direct sunlight or radiant heat from appliances might
affect control operation;
– on an outside wall;
– adjacent to, or in line with, conditioned air discharge grilles,
stairwells, or outside doors;
– where its operation may be affected by steam or water pipes or
warm air stacks in an adjacent partition space, or by an area
behind the thermostat which is not climate controlled;
– where its operation will be affected by the supply air of an adja-
cent climate control HVAC device; and
– near sources of electrical interference such as arcing relay
contacts.
REMOVING THE THERMOSTAT FROM THE SUBBASE
1. Insert a flat blade screwdriver or a coin 1/8' into the slot locat-
ed in the bottom center of the thermostat case and twist 1/4
turn. When you feel or hear a “click,” grasp the case from the
bottom two corners and separate from the subbase. Some
models require more force than others when separating due to
the number of terminals on the subbase.
2. Swing the thermostat out from the bottom.
3. Lift the thermostat up and off the subbase.
4. Place the rectangular opening in the subbase over the equip-
ment control wires protruding from the wall and, using the sub-
base as a template, mark the location of the two mounting
holes (exact vertical mounting is necessary only for appear-
ance).
5. Use the supplied anchors and screws for mounting on drywall
or plaster; drill two 3/16' (5mm) diameter holes at the marked
locations; use a hammer to tap the nylon anchors in flush to
the wall surface and fasten subbase using the supplied screws.
(Do not overtighten!)
6. Connect the wires from your system to the thermostat termi-
nals. Carefully dress the wires so that any excess is pushed
back into the wall cavity or junction box. Ensure that the wires
are flush to the plastic subbase. The access hole should be
sealed or stuffed to prevent drafts from the wall affecting the
thermostat.
7. Before the thermostat is reinstalled on the subbase, install the
optional clock/timer, indoor remote sensor and outdoor remote
sensor, if used. Refer to the installation instructions supplied
with each option. Also check the position of the DIP switches
on the back of the thermostat.
CAUTION
THIS DEVICE SHOULD BE INSTALLED BY A
QUALIFIED TECHNICIAN WITH DUE REGARD
FOR SAFETY, AS IMPROPER INSTALLATION
COULD RESULT IN A HAZARDOUS CONDITION
INSTALLATION INSTRUCTIONS (CONT)
REPLACING THE THERMO-
STAT ON SUBBASE
1. Position the thermostat on the
Robertshaw Programmable Thermostat Manual
hinged tabs at the top of the
subbase.
2. Gently swing the thermostat
down and press on the bottom
center until it snaps into place.
THERMOSTAT COVER LOCK
You may lock the cover down to
prevent unauthorized access to
the thermostat by adding the
clear plastic lock (included in the
installation bag.) Insert the plastic
lock piece into the bottom of the
mounted base. The ends of the
lock piece fit snugly under the
lock pins extending from the bot-
tom of the mounted base. The
tab in the middle of the lock piece
extends down from the base.
To release the locking mecha-
nism, press the lock piece up and
into the base while gently prying
open.
THERMISTOR MOUNTING INSTRUCTIONS
When placing the front cover on the thermostat ensure the
thermistor is not bent or misaligned.
Ensure that the thermistor does not touch the thermostat case.
The thermistor should be placed horizontal to the wall. Ensure the
thermistor is not pushed upward into the case.
The thermistor should be aligned so it is visible between the ribs
on the bottom of the subbase.
Outside rear view with backplate closed
WIRING DIAGRAM
Notes about the wiring diagram
Set it using'Up-Down' buttons and Press 'Mode/Alarm' button to set it.Step 7: After this, the Year will start blinking(ocupying entiredisplay) USE 'Up-Down' to set the correct Year. Ajanta quartz wall clock odc 130 user manual video. Set theDate,Month in similar way.Step 9: Once you have SET all correctly, Move the Slider Settingto 'Normal' (leftmost dot). (This is neccessaysince the Week Days.mon,tue etc can't be set manually.)Step 8: Next blinking will be Date and then Month.
• The Wiring Diagram shows how the R and 24V terminals are connected
when the shunt is in place and the thermostat and subbase are
snapped together. The dotted lines show the factory-supplied internal
connections.
• If the 24V(c) is not available from the equipment, the shunt may be
removed and a separate 24V transformer must then be used to power
the thermostat. To remove jumper (labeled JP1) from the printed circuit
board, pull straight out.
• This thermostat may be used with 24 Volt DC. The negative side of the
DC supply must be wired to the 24V (c) terminal.
TERMINAL DESIGNATIONS
W1 .......Auxiliary heat is energized as back-up or emergency
heat
Y1 .......Compressor is energized with a call for heating or
cooling
G ........Fan operates with a call for heating or cooling or by
pressing the FAN button.
Medonic m series user manual pdf. R ........Independent switching voltage*
24V ......24 VAC hot and common to power the thermostat
24V(c)
O........Energizes the reversing valve continuously in COOL
mode
B ........Energizes the reversing valve continuously in HEAT or
OFF modes
RS2......Use to connect up to 6 indoor and/or 1 outdoor
RS1......remote sensor/s.
RS+V
When connected the thermostat will automatically use
the indoor temperature sensor and not its own. Refer
to the instructions included with the sensor.
LED1 .....Free lights for status or function indication.
LED2
CLK1 .....Use with dry contact relay or remote clock/timer for
CLK2
alternate setpoints
*Allows for DC operation required on some older Lennox and McQuay units.
300-208
(For Release 3)
CAUTION
Power is supplied through the thermostat to the
remote devices. DO NOT connect any other 24V
source to the remote devices.